Видео

Greatest video on RUclips 💯

will the metal guard fit on a 2022 F150? I have the same fabric/POS splash guard now and might as well replace it.

My 2013 Escape S model with 2.5L engine has been great. 104,000 miles. There is a known issue on the 6F35 transmission but the trans drain n fill I did at 50k intervals seems to have prevented any issues. I do use Prolong transmission treatment. It made it very quiet and shifting became very smooth.

Get a Ronin drain plug and a piece of clear plastic tube.

If u could tell me how much oil would u put in a 3.9 9c1 Impala I’d appreciate it

I got a all black 9c3 pretty nice I'm fixing it up just a little. I really want a fold down rear seat still

Can u make a video on how to connect the wires from the inside of my spotlight? Wires were cut when I purchased the vehicle and maybe that’s the reason my spotlight isn’t working?

Crown vic >>>> impala

You dont even have to remove the mirror part. You can access access the tabs by pivoting the down and in on yhe inside edge 😂

Bad information

To spot a 2011 Impala 9C 1 I noticed it did not have ambient air sensor, I was thinking the center was bad until I found it missing went and bought one put it in, and OEM still don't see no temperature my question is did they even install a ambient temperature sensor in these police model cars

Does this splash guard fit 2019 f150 xlt supercab 3.3

Can this be used on a 2019 XLT Supercab 3.3 engine

Just got a 03 interior reminds me of my Vic I love it

I bought this same exact one, I have the same issue where I am missing the front mounting points, everything else fits what in the world is the difference

i would haul it around on a trailer

Eventually you might want to put that hood on the other car.

Has never dealt with winter. Would have more respect for it if it had.

Thanks I needed this information

Yeah my impala is making that stupid tampering noise.

I’m buying one this week.

You're a legend. Thanks for this video

I drive a black Impala 9c1 that looks exactly like his spotlight and everything except mine just has anime stickers all over it 😭

What rims are those?

THANKYOU! SO MUCH! FOR SHARING THIS INFO, IT HELPED ME OUT A LOT SIR. VERY GREATFUL. OWENS.

Guys, I have a standard cab 2020 F150 with the 6’ bed. When I tried to install this metal replacement, I found I did not have the frame holes needed to attach the forward most side brackets. The rear brackets and forward screws look like they’d match but not the additional side brackets. Thoughts?

Loosen the steering wheel locknut but don't remove it until wheel seperates from column. Then the steering wheel wont come flying at you when pulling.

Thank you! Very helpful. I just finished my installation and was flawless on my 2020 Platinum. If fact I didn't have the issue with the last bolt that you did. Mine mounted perfectly to the two previous front mounting points. Thanks again!

I have a 08 9C1 just replaced thermo 255908 on dash

I guess wesk paint to make it easier for departments to put logos on and take them off? Idk though just a guess

With all that dirt and grime on it almost looked like police car again 🙂

Looking good

Cleaned up pretty nice. Surprised the pressure washer didn’t rip the paint off.

Poor chassis.

A clean Vicky is a happy Vicky, running or not

Cleaned up decent dead vic is parts car

You should've swapped the hood from the dead car

Still shines up nicely

That rusty spot on the block looks like a coolant leak, which would explain the new gasket for the head. I've seen that a time or two on Ford's good ole 4.6 litre

Looks 100000X better nice work sir

nice Vicky I need to get one!

I would just get a car cover for it.

You need to use a random orbital sander at 120 grit the work you to 220. Use full and sand primer or spot putty . That’s a hack and pack way of doing it but it works

Lookin good! I have a dark blue Vic can attest that it looks fantastic

Also didn't you rattle can the hood already & it done it again even worst dam bro

Reminds me of my paint peeling vic

By bolt delete-does that mean they forgot to replace them 2 bolts? and with the delete- does it rattle much?

I like your way of measuring the holes. I don't have a center marker on the front of my bumper so I'll probably do it your way vs what the instructions say. Your holes are probably a smaller in size vs what the instructions say too, which is what I want. Nice work!

does it protect catalytic converter?

A portable steamer will help take the tint off the windows but be careful with the defrost lines on the rear window